Hello Guest, Log in!

Tube Bending Jig for 1 3/4" tubing

Tube Bending Jig for 1 3/4" tubing
Tube Bending Jig for 1 3/4' tubing
Your Price: $550.00
In Stock.
FREE Shipping
Part Number:TJ-210
  • -For 1 3/4" tube. Will also work with 1 1/2" to 2"
  • -Use the Tube Jig to mock up your tube, then copy it!
  • -Coped tube options - up to 80° copes for fancy tubes, or just up to 50° for the simple tubes

Choose Options

Select coped tubes
We finally have these back in stock, they are boxed up and ready to ship. The second picture show the revisions, we added notches every 90° to better transfer rotation numbers. The other improvement is a universal hinge with a wing nut to lock the hinge down.

Our Tube Jig lets you setup and adjust bends, rotation and copes on any tube. Then copy it and your final tube fits right the first time. No more guess work! Comes with everything you need to design, tweak and create any tube from a four bend main hoop to a simple coped tube and anything in between. Slots in the jig tubes are for measuring rotation of cope. The bend centerline is easy to transfer to tangent/start of bend.

-Laser cut tubing with cope angles and rotation slots
-For 1 3/4" tube. Will work with one size above or below
-Includes 2 small and 2 large hinges along with extension tubes
-Full kit comes w/ pair of every cope angle in 10° increments up to 70° and one 80°
-50 degree kit does not include 60°/70° and 80° coped tubes
-Yellow Zinc plated and black oxide on the small tubes
-Telescoping tube with overlapping lengths lets you put a cope and bend anywhere you want
-Large yellow tubes are 1 3/4" x .120 wall and small black tubes are 1 1/2" x .095

This tool will save you time, it only takes a couple minutes to setup. Then you get to look at the tube jig, adjust it for a perfect fit and have all of your measurements ready to copy. This also lets you be confident that you bend once, notch once and the tube fits right the first time. Another benefit is less wasted material from missing a rotation or having to guess where a cope is going to end up. The Tube Jig might be a new product, but we have been using and improving the prototype for the last five years. So you can rest assured that this tool is designed right!

Includes a pair of every cope angle in 10° increments from 0° to 80°, this helps to make sure your cope rotation will be correct. Thumb screws are used as jam bolts which hold strong and are easy to tweak distance and rotation. These are perfect copes for 1 3/4" tube, but also works for other sizes. On 1 1/2" tube the copes will have a little rotational slop, which is easy to center. On 2" tube the copes will fit tight for rotation, but will have a slight gap on the long side of cope, add that gap when you go to notch the final tube. Every coped tube has two slots which allow you to measure the rotation of cope. Drop a piece of 1/8" flat bar in and then use a magnetic rotation gauge to measure.

The hinges are another great feature, use the small black ones when a cope is right next to a bend. Switch to the big yellow hinges for large tubes with multiple bends. You can also put the hinges together for bending tube over 110° all the way to 180°. Each hinge has a long and short side which overlap, so if you run out of room just flip to the next side. The pivot point is the center of tube and bend center line. This is easy to transfer to tangent/start of bend using an angle finder and the radius die on your bender.
5 Stars
Time saver
I wasn’t sure how it was going to work, but I have been quite impressed with it. It’s cut down tremendously on waste, let’s you get the perfect notch angle every time, it’s not a tool just for amateurs, it really does work. Makes mirroring the other side on complicated multiple plane bends much easier.
Did you find this helpful?  2 of 2 Found Helpful
Reviewed by:  from Louisiana . on 10/8/2018
5 Stars
Works great!
It was easy to setup and figure out pretty quick. The coped tube ends are great, even for straight tubes. I made some longer extension tubes for the jig, which made it easier to setup on the larger tubes. I did a hybrid exo cage on a FJ60 and I couldn't have done it without the jig.
Did you find this helpful? 
Reviewed by:  from Georgia. on 1/25/2021

Related Items