Beefcake Plate - 1/4" Top for Harbor Freight Fixture Table

1 Review(s) Write a Review

Your Price: $225.00

Part Number: FXH-22

Availability: In Stock. FREE Shipping

- Replace or upgrade the top of your budget fixture table

- Best used with two tables, let's you double up the other table tops

- Includes two 1/4" thick 18x24" plates to cover your 36x24 table

- FREE shipping in two boxes

Quantity

Description
Customer Reviews

These let you replace or upgrade the top of your budget fixture table. They are best used with two tables, use this on one and then double the tops up on your other table. This lets you use fixture clamps that lock down tight and won't egg out the holes.

- 1/4" steel top plates come pre-chamfered and ready to bolt on.

- Two 18x24 plates will cover your 36x24 table

Rating Snapshot

Select a row below to filter reviews.

Average Customer Ratings

5.0

If your thinking about buying this

This plate is great square and even, harbor freights plate is sadly not. I ran into some issue but here’s how I fixed them. 1. Line up one plate as close as you can get to matching up with the 5/8 holes 2. Place the pucks from you’re 5/8 harbor freight kit into each corner ( the problem I had was I couldn’t get one corner because the harbor freight plate was not true, so I got as close as possible) 3. Place the mounting hardware on the corners do not put the bolts in the center you will make it harder on yourself to put on the next plate ( I had 1 bolt that would not go in easily so I had to use a 5/16 drill bit to make the hole perfectly straight with the harbor freight plate so the bolt would pass through easily, again harbor freight quality control not the plate.) 4. Tighten the mounting hardware down with the pucks still in ( don’t worry if one of the pucks don’t go in fully) 5. Repeat same above 4 steps on the other side 6. Once both places are in place the center mounting bolts in and tighten them. 7. Now you will notice there is some holes that will not line up with the pucks, what you will need to do is get a 5/8 drill bit and clean out those holes. I went through every hole and cleaned it out so I wouldn’t have any problems (took about 12 mins in total. Once you’ve done that your harbor freight table will now be a table you can use. Originally when these problems came up it was frustrate after I was expecting a quick drop in. After talking on the phone with 911motorsports who didn’t know at the time of writing this that this was an issue. They had come to the same problem which there own table. Where a section of holes didn’t line up. Now this is a no way a mistake on their part, the plate is square and plumb problem was that harbor freights table was slightly off by 1mm and just needed some slight drilling. It sucks but what can you do and take 30 mins to do it right and never have to worry about it again. Side note the plates sent line up perfectly with the frame no drilling needed so if you want to skip doing all that drilling just take it off and add this one on. I have added some pictures from how it lined up when I originally tried to put it on.

Did you find this helpful? 2 of 2 Found Helpful

Reviewed by: (Verified Buyer) Matt from Illinois on 9/20/2024

Magnetic Plasma Guide Holder 2 pc. - for Plasma Stencils and Straight Edge

$50.00

In Stock. FREE Shipping

(4)

Add To Cart

Spare Tire Flip Mount - 2019+ Mercedes G-class - W463A chassis

$650.00

In Stock. FREE Shipping

Select Options

Push the Limits - T shirt - Gray

$20.00

In Stock. FREE Shipping

Select Options

Floor Jack Skid Plate

$25.00

In Stock. FREE Shipping

Select Options

Pocket Screw Driver

$3.00

In Stock. FREE Shipping

Add To Cart

PT-60 Flat Cutting Tip Set - Plasma Torch Consumables

$48.00

In Stock. FREE Shipping

Select Options

Beefcake Plate - 1/4" Top for Harbor Freight Fixture Table

Related Items